Maxon MODMAX MM-6280IND Informações Técnicas

Extended AT Commands Manual VERSION 2.1 FW V 2.1.3 This document is the sole and exclusive property of Maxon Australia. Not to be

Extended AT Commands Manual Page 10 of 70 2009-06-25 1.2. Terms The following terms are used throughout this document. We have provided and expla

Extended AT Commands Manual Page 11 of 70 2009-06-25 Term Description PSTN Public Switched Telephone Network refers primarily to the telephone sy

Extended AT Commands Manual Page 12 of 70 2009-06-25 2. AT INTERFACE DESCRIPTION 2.1. Basic Integration The modem supports asynchronous serial c

Extended AT Commands Manual Page 13 of 70 2009-06-25 2.3. Command Format The AT command set in UART1 is based on ASCII text. The extended AT com

Extended AT Commands Manual Page 14 of 70 2009-06-25 3. BASIC INTERFACE CONFIGURATION 3.1. Baud Rate Set-up This section provides basic informat

Extended AT Commands Manual Page 15 of 70 2009-06-25 Special: Set command Command TE2 Æ MT2 $$Connect_Baud=<value> Response TE2 Å MT2 $$

Extended AT Commands Manual Page 16 of 70 2009-06-25 Command TE2 Æ MT2 $$NOTIFCNT? Value 0: No notification (No boot alert message, No SMS messa

Extended AT Commands Manual Page 17 of 70 2009-06-25 4. SIGNAL INFORMATION 4.1. MT SMS Table 4-10 Status Signal Action AT SMS Notification to

Extended AT Commands Manual Page 18 of 70 2009-06-25 5. INTERFACE ENVIRONMENT 5.1. MT2 Basic Operational State. This command set enables the use

Extended AT Commands Manual Page 19 of 70 2009-06-25 Table 5-14 Read command Command TE2 Æ MT2 $$EMMOREG? Response TE2 Å MT2 $$EMMOREG: period,

RF EXPOSURE COMPLIANCE The use of this device in any other type of host configuration may not comply with the RF exposure requirements and should be

Extended AT Commands Manual Page 20 of 70 2009-06-25 Command TE2 Æ MT2 $$RESET Response TE2 Å MT2 $$RESET: 1 | 0 (Success | Failure) Note: U

Extended AT Commands Manual Page 21 of 70 2009-06-25

Extended AT Commands Manual Page 22 of 70 2009-06-25 5.2.1.2. LED control (AT$$EXT_LED) This command is used for control of the LED’s on-time. C

Extended AT Commands Manual Page 23 of 70 2009-06-25 5.3.1.1. SMS low battery voltage set point (AT$$LOWBATT_VTG) This command also sets the SMS

Extended AT Commands Manual Page 24 of 70 2009-06-25 5.4. Visual/Audible Call Alert Options 5.4.1.1. Receiving notification mode option (AT$$RCV

Extended AT Commands Manual Page 25 of 70 2009-06-25 Command TE2 Æ MT2 $$RINGIDX=<value> Response TE2 Å MT2 <result_code> (OK | ER

Extended AT Commands Manual Page 26 of 70 2009-06-25 5.5.1.4. Modem scheduled Information (AT$$Ping) Scheduled information will include Antenna S

Extended AT Commands Manual Page 27 of 70 2009-06-25 Command TE2 Æ MT2 $$CURRSTATE Value -1: Offline 0: Idle state 1: Initialisation state 2: Al

Extended AT Commands Manual Page 28 of 70 2009-06-25 6. DIAGNOSTIC COMMANDS These commands are used for testing and diagnostic purposes. They can

Extended AT Commands Manual Page 29 of 70 2009-06-25 Command TE2 Æ MT2 $$RSSI_LEVEL? Value Default settings in –dBm units: Upper: 95 (-dBm) Stro

REVISION HISTORY Product Name Maxon ModMax - MM-6280IND Document Type Public Current Version Number 2.1 Status of the Document Public Release R

Extended AT Commands Manual Page 30 of 70 2009-06-25 7. DATA CALL SET-UP The following tables describe MO data call procedures. Call released or

Extended AT Commands Manual Page 31 of 70 2009-06-25 8. SMS commands 8.1.1. General Configuration Commands 8.1.1.1. Select Message Service +CSM

Extended AT Commands Manual Page 32 of 70 2009-06-25 Table 24. +CPMS action command syntax Command Possible response(s) +CPMS=<mem1>[, <

Extended AT Commands Manual Page 33 of 70 2009-06-25 304 invalid PDU mode parameter 305 invalid text mode parameter 310 (U)SIM not inserted 311

Extended AT Commands Manual Page 34 of 70 2009-06-25 same commands, but only when the length of the SMSC address coded into <pdu> parameter

Extended AT Commands Manual Page 35 of 70 2009-06-25 8.1.1.9. Informative Examples In this example, the volatile parameter settings of TA are u

Extended AT Commands Manual Page 36 of 70 2009-06-25 and replaced with the new received indications. 1 Discard indication and reject new received

Extended AT Commands Manual Page 37 of 70 2009-06-25 0 No CBM indications are routed to the TE. 1 If CBM is stored into ME/TA, indication of the

Extended AT Commands Manual Page 38 of 70 2009-06-25 NOTE: If the selected <mem1> can contain different types of SMs (e.g. SMS-DELIVERs, SMS

Extended AT Commands Manual Page 39 of 70 2009-06-25 ,<dcs>,[<vp>], <sca>,<tosca>,<length>]<CR><LF><d

CONTACT INFORMATION Depending on the nature of your inquiry, please feel free to contact the following senior personnel: Sales, Marketing & Cor

Extended AT Commands Manual Page 40 of 70 2009-06-25 8.1.1.14. Informative Examples Setting new message indications: AT+CNMI=? (query new mes

Extended AT Commands Manual Page 41 of 70 2009-06-25 error, final result code +CMS ERROR: <err> is returned. See chapter Message Service Fai

Extended AT Commands Manual Page 42 of 70 2009-06-25 message upon unsolicited delivery status report result code. If sending fails in a network or

Extended AT Commands Manual Page 43 of 70 2009-06-25 [,<callback_num>] [,<timestamp>] <CR> text is entered<ctrl-Z/ESC> AT+

Extended AT Commands Manual Page 44 of 70 2009-06-25 Command Possible response(s) if text mode (+CMGF=1): +CMGC=<fo>,<ct>[,<pid>

Extended AT Commands Manual Page 45 of 70 2009-06-25 Storing an unsent message in memory, sending it from there, and deleting it: AT+CPMS?

Extended AT Commands Manual Page 46 of 70 2009-06-25 9. SMS Processing Options 9.1.1. SMS Send and Receive Options 9.1.1.1. SMS Mail Notificati

Extended AT Commands Manual Page 47 of 70 2009-06-25 9.1.1.3. SMS Mail Notification Option (SMSOPT=1) Notify TE2 Å MT2 Received SMS: <time s

Extended AT Commands Manual Page 48 of 70 2009-06-25 9.1.2. Auto delete Messages in ME Memory 9.1.2.1. Auto Delete Messages in ME memory($$AUTO

Extended AT Commands Manual Page 49 of 70 2009-06-25 10. Modem SMS Remote Reporting 10.1.1. SMS Auto Voltage Alert Maxon have integrated advance

Extended AT Commands Manual Page 5 of 70 2009-06-25 TABLE OF CONTENTS Extended AT Commands Manual ...

Extended AT Commands Manual Page 50 of 70 2009-06-25 10.1.1.3. SMS $$LOWBATT 1 set recipient number (AT$$AUTO_SMS) Table 10-63 Read command Comma

Extended AT Commands Manual Page 51 of 70 2009-06-25 Command TE2 Æ MT2 $$REMOTE_CTRL=<VALUE> Response TE2 Å MT2 $$REMOTE_CTRL: <VALUE&

Extended AT Commands Manual Page 52 of 70 2009-06-25 Command from SMS phone Enter directory number of specific MT2 Enter message “maxon.rssi” (not

Extended AT Commands Manual Page 53 of 70 2009-06-25 10.1.2.8. Remote Reset Reset the modem. Table 10-73 Read command Command from SMS phone Ent

Extended AT Commands Manual Page 54 of 70 2009-06-25 11. NVM vs. USER PROFILE STORAGE The following table indicates for each command listed, where

Extended AT Commands Manual Page 55 of 70 2009-06-25 12. TIA/EIA/IS-707A AT COMMAND SET 12.1.1. User modified profiles & NVM changes 12.1.1.1

Extended AT Commands Manual Page 56 of 70 2009-06-25 12.2. Basic AT Commands The following table specifies the basic AT parameters to be supported

Extended AT Commands Manual Page 57 of 70 2009-06-25 Parameter Description Packet Data STU-III &C1 Circuit 109 (CF) ON in accordance with the

Extended AT Commands Manual Page 58 of 70 2009-06-25 Register Value Description Packet Data STU-III S7 1 to 255 [50] Number of seconds to establ

Extended AT Commands Manual Page 59 of 70 2009-06-25

Extended AT Commands Manual Page 6 of 70 2009-06-25 5.4. Visual/Audible Call Alert Options...

Extended AT Commands Manual Page 60 of 70 2009-06-25 12.2.4. Basic result codes The following table specifies the Basic Result Codes to be suppor

Extended AT Commands Manual Page 61 of 70 2009-06-25 Command Value per Description Packet Data +GCAP IS-131 This extended-format command causes t

Extended AT Commands Manual Page 62 of 70 2009-06-25 Command Value per Description Packet Data +ICF IS-131 TE2-MT2 Character Framing. This extend

Extended AT Commands Manual Page 63 of 70 2009-06-25 Command Value per Description Packet Data +IFC IS-131 TE2-MT2 Local Flow Control. This exten

Extended AT Commands Manual Page 64 of 70 2009-06-25 Command Value per Description Packet Data +IPR IS-131 Fixed Rm Rate. This numeric extended-f

Extended AT Commands Manual Page 65 of 70 2009-06-25 13. Multiplexing 13.1.1. RM3 (AT$$NOTI_DS) Command to activate the RM3 feature of the mode

Extended AT Commands Manual Page 66 of 70 2009-06-25 14. CELLULAR EXTENDED AT COMMAND SET AT command lines containing the command set specified sta

Extended AT Commands Manual Page 67 of 70 2009-06-25 14.1.2. Cellular identification AT command extensions Table 14.86 Cellular identification AT

Extended AT Commands Manual Page 68 of 70 2009-06-25 14.1.3. Cellular result codes for Asynchronous data services Table 14.87 Cellular result cod

Extended AT Commands Manual Page 69 of 70 2009-06-25 15. DM COMMAND (DIAGNOSTIC MODE) All the AT command set can be used at UART2 DM port with Asyn

Extended AT Commands Manual Page 7 of 70 2009-06-25 8.1.1.18. Write Message to Memory +CMGW...

Extended AT Commands Manual Page 70 of 70 2009-06-25 16. CARRIER COMMAND OPTIONS 16.1.1. Debug screen (AT$$DBGSCRN) This command reads Debug Scree

Extended AT Commands Manual Page 8 of 70 2009-06-25 14. CELLULAR EXTENDED AT COMMAND SET .....

Extended AT Commands Manual Page 9 of 70 2009-06-25 1. OVERVIEW The modem is a rugged, full duplex Data and SMS modem designed to operate on 3G